推拉棚安裝中我們需要注意那些步驟與注意細節？濟南推拉棚廠家的小編來給大家分享一下。

What steps and details should we pay attention to during the installation of the sliding shed? Jinan push-pull shed manufacturer's small editor to share with you.

一．主架安裝說明：

1、 Main frame installation instructions:

主架有兩種，一種是主架分半，另一種是主架是一整體的，主架是一整體的就不需要理會了，那來說說主架分半的：

There are two kinds of main shelves. One is that the main shelf is divided into two parts, and the other is that the main shelf is integrated. If the main shelf is integrated, you don't need to pay attention to it. Let's talk about the main shelf divided into two parts:

看主架橫梁有沒有剪刀架；無伸縮剪刀架，無需理會；有伸縮剪刀架，需要把分半主架拼接，拼接時注意：主架一半橫梁是螺桿，一半橫梁是伸縮圈，在拼接的時候，一個主架一半是螺桿，一半是伸縮圈；（注意：不能一個主架全是螺桿，一個主架全是伸縮圈），在主架拼接中間廠家會匹配螺絲作為固定。

Check whether the beam of the main frame has a scissors frame; No telescopic scissors stand, no need to pay attention; There is a telescopic scissor frame, so it is necessary to splice the main frame in half. During splicing, attention should be paid to: half of the crossbeam of the main frame is a screw, and half of the crossbeam is a telescopic ring. During splicing, one main frame is half a screw, and half is a telescopic ring; (Note: One main frame cannot be all screws, and one main frame can be all expansion rings). The manufacturer will match screws for fixation in the middle of main frame splicing.

二．立柱安裝說明：

2、 Column installation instructions:

主架部分生產制作時就弄好了，就來開始立柱了，立柱一般我們是完整的，有些比較長尺寸的產品，我們的立柱也會分開，這個連接起來就簡單一些，我們只需要參考立柱前半部分伸縮剪刀架方向，后面都是一致的；弄好之后，我們把立柱豎起來，一邊一個人扶住立柱，立柱豎起來，需要找一根橫條第三人就可以把主架插在兩邊的立柱上了。

When the main frame is produced, it is ready to start the column. Generally, we are complete with columns. For some products of relatively long size, our columns will also be separated. This connection is simpler. We only need to refer to the direction of the telescopic scissors frame in the front half of the column, and the rear is consistent; After that, we will erect the column. One person will hold the column, and the column will be erected. A third person needs to find a horizontal bar to insert the main frame onto the columns on both sides.

三．頂部安裝說明：

3、 Top installation instructions:

主架和立柱都安裝好了，現在就開始來上頂篷布了；把打包好的頂部篷布拆開，打開，找出推拉棚篷布的長、寬；上頂部時，需從長的左右反向上，不可從寬的前后上，避免上頂部時出現人員不注意，推拉棚往前后傾斜，發生意外，二節約后期費力費時間；頂部篷布完整搭好后，撐開立柱，在頂部與橫梁中滴上生產部配的膠水，如果側面有圍布那么先不要固定側面下垂的布料；沒有就圍布，立柱上部分側面有蝴蝶螺絲，用蝴蝶螺絲固定頂部下垂篷布。

The main frame and column have been installed, and the tarpaulin is now ready; Disassemble the packed top tarpaulin, open it, and find out the length and width of the sliding tarpaulin; When climbing the top, it is necessary to move from the left to the right in a long direction, not from the front to the back in a wide direction, so as to avoid carelessness when climbing the top, and to push and pull the shed forward and backward, which may cause accidents; After the top tarpaulin is completely erected, the column shall be stretched, and the glue prepared by the production department shall be applied to the top and the beam. If there is a shroud on the side, do not fix the hanging cloth on the side first; If there is no surrounding cloth, there are butterfly screws on the upper side of the column, and the top drooping tarpaulin is fixed with butterfly screws.

四．四周圍布安裝說明（沒有四周圍布的客戶，可以忽略）：

4、 Installation instructions for surrounding cloth (customers without surrounding cloth can ignore):

長兩側的圍布：從一個立柱上部分蝴蝶螺絲固定，邊固定側面，現在也可以固定頂部下垂布料，方式是里面是圍布，外面是頂部，這樣下雨了，雨水會隨著頂部布料，流向側面圍布，順著到地面，注:不可頂部下垂布料在里面，圍布在外面。

Surrounding cloth on both sides of the long column: fix it with butterfly screws on the upper part of a column, and fix the side at the same time. Now you can also fix the hanging cloth on the top. The way is that the inside is the surrounding cloth, and the outside is the top. When it rains, the rain will flow with the top cloth to the side surrounding cloth, and along the ground. Note: The hanging cloth on the top cannot be inside, but the surrounding cloth is outside.

寬兩面的圍布：寬面的安裝圍布有兩種，一種是前圍是分開的，一種是后圍是一整塊的；分開的主架的兩邊是有一個圈圈螺帽的，生產部會配好花籃螺栓與鋼絲繩，用來支撐前后圍，現在可以掛圍布了，圍布我們相隔40公分到50公分會有一個扣眼，一個一個掛上就好了，如果是后圍是一整塊的，和前圍的安裝方法是一樣的，zui后一步就是把兩邊的圍布和立柱鏈接起來，我們會配膠水，粘接在一起就好了。

Wide two side shroud: there are two kinds of wide side installation shroud, one is that the front shroud is separated, the other is that the back shroud is a whole piece; There is a ring nut on both sides of the separated main frame. The production department will provide basket bolts and steel wire ropes to support the front and rear walls. Now we can hang the shroud. We will have a buttonhole at a distance of 40 cm to 50 cm. If the rear wall is a whole block, the installation method is the same as that of the front wall. Zui will link the shroud on both sides with the column next step, and we will prepare glue, Just glue it together.

五．固定安裝說明：

5、 Fixed installation instructions:

現在推拉棚整個都已經組裝好了，也可以使用了，在使用前，做一下固定，讓推拉棚在使用期間壽命更久一些，基本固定有兩種：一種是輪子固定，我們會配鏈條與頂爆螺絲，在輪子部位與地面做一個固定；還有一種就是，拉鋼絲繩，在推拉棚前后四個方向做好一個拉繩的固定，這樣在大風來臨的時候，可以預防被大風吹跑；還有一些其他的固定，這個就看推拉棚的特殊，會有一些特殊的固定。

Now the whole sliding shed has been assembled and can also be used. Before use, fix it to make the sliding shed have a longer service life. There are basically two kinds of fixing: one is wheel fixing. We will provide chains and top blasting screws to fix the wheel with the ground; Another way is to pull the wire rope and fix it in four directions before and after the sliding shed, so that when the wind comes, it can prevent it from being blown away by the wind; There are also some other fixation, which depends on the special features of the sliding shed. There will be some special fixation.

此外推拉棚因為在戶外受風輕輕吹日曬淋雨，為了更好地增加使用壽命，須對電動推拉棚開展恰當的維護保養和防護。以上就是濟南推拉棚的安裝步驟分享，感謝瀏覽，如果你有需要，歡迎來我們網站//483111.com.cn進行咨詢！

In addition, because the push-pull shed is exposed to the wind, sun and rain, proper maintenance and safety protection must be carried out for the electric push-pull shed in order to better increase its service life. The above is the installation steps of Jinan push-pull shed. Thank you for browsing. If you need, please come to our website //483111.com.cn Consult!